Process & Material
Tungsten Copper Micro EDM High Precision Tolerance + Skim Cut / Fine Pass Finish Review
This Tungsten Copper Micro EDM page combines a High-precision tolerance target with a Skim-cut / fine pass finish surface target. These requirements must be planned together because finishing passes improve texture while also changing profile offset, cavity size, hole size, or edge geometry.
Quick Answer
For Tungsten Copper, ±0.005–0.010 mm and Ra 0.4–0.8 μm are achievable on selected Micro EDM features when electrode wear, gap stability, micro-flushing, thermal control, and measurement resolution are planned together. Apply both targets from the same datum, and reserve the tightest values for the dimensions and faces that control function.
Key Quality Decisions
What These Targets Mean
On Tungsten Copper, ±0.005–0.010 mm controls the named dimensions and Ra 0.4–0.8 μm controls the named functional faces. In Micro EDM, electrode wear and measurement resolution can consume the tolerance while low-energy finishing changes edge radius and texture. The supplied condition adds a separate risk: local composition, porosity and brittle tungsten-rich edges can create nonuniform discharge and chipping.
Getting Both Targets Right
Use one machining and inspection datum. Apply ±0.005–0.010 mm only to dimensions that control fit, and Ra 0.4–0.8 μm only to functional faces. Plan electrode wear, feature-to-electrode ratio, micro-flushing, aspect ratio, edge radius, thermal stability, and measurement resolution. State the exact Tungsten Copper condition and the inspection method before releasing the result.
What Gets Missed
On a sub-millimeter hole, slot, or pitch feature specified at ±0.005–0.010 mm and Ra 0.4–0.8 μm, electrode wear and measurement uncertainty can consume the remaining tolerance while the edge rounds during finishing. The tolerance represents a small remaining offset allowance, while successive low-energy passes change kerf, taper, and corner geometry while improving texture; treating them as independent callouts can make the last finishing step destroy the dimension it is meant to improve. Inspect size, pitch, depth, edge radius, electrode wear, and measurement uncertainty after the final surface step. For Tungsten Copper, also account for this material-specific risk: local composition, porosity and brittle tungsten-rich edges can create nonuniform discharge and chipping.
How the Targets Interact
For Tungsten Copper, ±0.005–0.010 mm and Ra 0.4–0.8 μm are linked through the Micro EDM finishing route. Electrode wear and measurement resolution can consume the tolerance while low-energy finishing changes edge radius and texture. The release plan must bind material condition, geometry, datum, finishing stage, and measurement to the same named features.
Micro EDM Capability Reference
| What you're asking | What you can expect |
|---|---|
| Feature types | micro holes, micro slots, miniature cavities, fine pins, and sub-millimeter precision details |
| Tolerance | ±0.002–0.010 mm |
| Surface finish | Ra 0.1–1.6 μm |
| Feature scale | Sub-millimeter holes, slots, and cavities |
| Primary micro limit | Electrode wear and measurement resolution |
| Main limitation | Loose-tolerance or easily accessible features are rarely economical with Micro EDM. |
Quality Target Reference
| Requirement | Planning range | What it means in practice |
|---|---|---|
| High-precision tolerance | ±0.005–0.010 mm | Plan finishing passes, thermal stability and inspection from the same datum scheme. |
| Skim-cut / fine pass finish finish | Ra 0.4–0.8 μm | Use dedicated trim or finishing passes and inspect only the surfaces carrying this callout. |
Material Condition Reference
| Condition | What to expect | Watch out for | Surface notes |
|---|---|---|---|
| annealed | Use gentle fixturing and adjust energy for high conductivity. | Soft edges can mark or roll under poor support. | Keep contact, bearing, and cosmetic faces as separate finish requirements. |
| half-hard or work-hardened | Balance work-hardening stress with wear compensation. | Thin sections can move and micro features can round as electrodes wear. | Inspect edge radius and functional texture. |
Tolerance & Surface Requirements
For Micro EDM at ±0.005–0.010 mm and Ra 0.4–0.8 μm, apply the finish only to the faces named on the drawing. On Tungsten Copper, use gentle fixturing and a finish strategy that protects contact, sealing or heat-transfer surfaces. Roughness does not replace recast, edge, corrosion, crack, or post-process acceptance where those items affect function.
Tungsten Copper Micro EDM Quality Checkpoints
- Mark the dimensions that actually need ±0.005–0.010 mm and use the same datum for machining and inspection.
- Circle the faces that need Ra 0.4–0.8 μm; leave nonfunctional surfaces at a practical production finish.
- State the Tungsten Copper condition, Micro EDM finishing strategy, measurement method, and any recast or edge requirement.
Limits and Better Alternatives
Main Limit
±0.005–0.010 mm and Ra 0.4–0.8 μm are selected-feature planning references for Tungsten Copper in Micro EDM, not unconditional whole-part guarantees.
Consider Another Route When
Use conventional EDM for larger features, precision laser processing for suitable thin geometry, or mechanical micro-drilling where a tool can reach.
Practical Next Step
Send the Tungsten Copper drawing with the Micro EDM features that need ±0.005–0.010 mm, the faces that need Ra 0.4–0.8 μm, the supplied condition, quantity, datums, and inspection method.
Practical Takeaway
On Tungsten Copper, plan ±0.005–0.010 mm and Ra 0.4–0.8 μm together for the selected Micro EDM features. Use one datum and one inspection plan, and apply the tightest values only where they control function.
Additional Project Information
Include application, destination and end-use notes together with the material, quantity and drawing requirements.
Project Details for Technical Review
Include application and end-use notes when they affect material, inspection, documentation, or export review.
- Process: Micro EDM
- Material: Tungsten Copper
- Drawing or part sketch
- Material grade
- Thickness / part size
- Quantity
- Tolerance and critical dimensions
- Surface finish or inspection requirement
STEP/STP, DXF, DWG, PDF, IGS/IGES or ZIP.
Confidential drawing review. NDA support available on request.