Process & Material
Tellurium Copper Wire EDM High Precision Tolerance + Standard Finish Review
This Tellurium Copper Wire EDM page combines a High-precision tolerance target with a Standard surface target. These requirements must be planned together because finishing passes improve texture while also changing profile offset, cavity size, hole size, or edge geometry.
Quick Answer
For Tellurium Copper, ±0.005–0.010 mm and Ra 1.6–3.2 μm are achievable on selected Wire EDM features when wire tension, guide alignment, kerf compensation, flushing, and planned trim passes are planned together. Apply both targets from the same datum, and reserve the tightest values for the dimensions and faces that control function.
Key Quality Decisions
What These Targets Mean
On Tellurium Copper, ±0.005–0.010 mm controls the named dimensions and Ra 1.6–3.2 μm controls the named functional faces. In Wire EDM, trim passes correct profile offset and texture together, so guide alignment, flushing, and the final wire offset affect both targets. The supplied condition adds a separate risk: soft conductive edges and mixed thermal response can make fixturing and finish control more important than cutting force.
Getting Both Targets Right
Use one machining and inspection datum. Apply ±0.005–0.010 mm only to dimensions that control fit, and Ra 1.6–3.2 μm only to functional faces. Plan wire diameter, kerf compensation, flushing, wire tension, guide alignment, taper, and trim-pass stability. State the exact Tellurium Copper condition and the inspection method before releasing the result.
What Gets Missed
On a narrow slot or profile specified at ±0.005–0.010 mm and Ra 1.6–3.2 μm, the top contour can be correct while the lower wall retains taper or a corner opens after the final trim. The tolerance represents a small remaining offset allowance, while the last production pass changes both texture and final size; treating them as independent callouts can make the last finishing step destroy the dimension it is meant to improve. Inspect top, bottom, verticality, kerf, and internal radius after the final surface step. For Tellurium Copper, also account for this material-specific risk: soft conductive edges and mixed thermal response can make fixturing and finish control more important than cutting force.
How the Targets Interact
For Tellurium Copper, ±0.005–0.010 mm and Ra 1.6–3.2 μm are linked through the Wire EDM finishing route. Trim passes correct profile offset and texture together, so guide alignment, flushing, and the final wire offset affect both targets. The release plan must bind material condition, geometry, datum, finishing stage, and measurement to the same named features.
Wire EDM Capability Reference
| What you're asking | What you can expect |
|---|---|
| Feature types | through profiles, precision slots, punches, inserts, cutouts, narrow webs, and tapered walls |
| Tolerance | ±0.005–0.025 mm |
| Surface finish | Ra 0.2–3.2 μm |
| Wire diameter | 0.10–0.30 mm planning range |
| Minimum internal corner | Approximately wire radius plus spark gap |
| Main limitation | Blind cavities and closed pockets are not wire-cut features. |
Quality Target Reference
| Requirement | Planning range | What it means in practice |
|---|---|---|
| High-precision tolerance | ±0.005–0.010 mm | Plan finishing passes, thermal stability and inspection from the same datum scheme. |
| Standard finish | Ra 1.6–3.2 μm | A practical production finish for many nonsealing and noncosmetic features. |
Material Condition Reference
| Condition | What to expect | Watch out for | Surface notes |
|---|---|---|---|
| annealed | Use gentle fixturing and adjust energy for high conductivity. | Soft edges can mark or roll under poor support. | Keep contact, bearing, and cosmetic faces as separate finish requirements. |
| half-hard or work-hardened | Balance work-hardening stress with wear compensation. | Thin sections can move and micro features can round as electrodes wear. | Inspect edge radius and functional texture. |
Tolerance & Surface Requirements
For Wire EDM at ±0.005–0.010 mm and Ra 1.6–3.2 μm, apply the finish only to the faces named on the drawing. On Tellurium Copper, use gentle fixturing and a finish strategy that protects contact, sealing or heat-transfer surfaces. Roughness does not replace recast, edge, corrosion, crack, or post-process acceptance where those items affect function.
Tellurium Copper Wire EDM Quality Checkpoints
- Mark the dimensions that actually need ±0.005–0.010 mm and use the same datum for machining and inspection.
- Circle the faces that need Ra 1.6–3.2 μm; leave nonfunctional surfaces at a practical production finish.
- State the Tellurium Copper condition, Wire EDM finishing strategy, measurement method, and any recast or edge requirement.
Limits and Better Alternatives
Main Limit
±0.005–0.010 mm and Ra 1.6–3.2 μm are selected-feature planning references for Tellurium Copper in Wire EDM, not unconditional whole-part guarantees.
Consider Another Route When
Use Sinker EDM for blind forms, CNC for accessible open geometry, or laser/waterjet when sheet-cutting speed matters more than EDM edge quality.
Practical Next Step
Send the Tellurium Copper drawing with the Wire EDM features that need ±0.005–0.010 mm, the faces that need Ra 1.6–3.2 μm, the supplied condition, quantity, datums, and inspection method.
Practical Takeaway
On Tellurium Copper, plan ±0.005–0.010 mm and Ra 1.6–3.2 μm together for the selected Wire EDM features. Use one datum and one inspection plan, and apply the tightest values only where they control function.
Technical Reference
Use the values as planning references and define the functional requirement on the controlled drawing.
Use This Guide to Prepare Your RFQ
Contact us when your drawing and requirements are ready for review.
- Process: Wire EDM
- Material: Tellurium Copper
- Drawing or part sketch
- Material grade
- Thickness / part size
- Quantity
STEP/STP, DXF, DWG, PDF, IGS/IGES or ZIP.
Confidential drawing review. NDA support available on request.