Process & Material
Tellurium Copper Sinker EDM Thickness Review (20–50 Mm)
Tellurium Copper at 20–50 mm changes how Sinker EDM must be supported, flushed, finished, and inspected. The controlling dimension is cavity depth and width, rib thickness, electrode access, electrode wear, flushing and debris evacuation, not merely the outside stock size.
Quick Answer
For Sinker EDM on Tellurium Copper, treat 20–50 mm as a setup input rather than a guaranteed accuracy band. Confirm the real cavity depth and width, rib thickness, electrode access, electrode wear, flushing and debris evacuation, material condition, datum, functional faces, and inspection method before assigning tolerance or finish.
Key Thickness Decisions
What This Thickness Range Means
Do not convert stock thickness into cavity depth. Deep-cavity decisions must use the actual depth, width and rib aspect ratio. On Tellurium Copper, the supplied condition still changes support and surface response. This is the Sinker EDM thickness decision; it does not turn the range into a machine promise.
Choosing the Right Setup
For Sinker EDM on Tellurium Copper at 20–50 mm, plan electrode material, wear compensation, cavity depth, rib width, orbit strategy, and debris evacuation. Then state the supplied condition, support the functional features, and define surface and inspection requirements separately. Apply the tightest tolerance and finest finish only to the dimensions and faces that control function.
What to Watch For
At 20–50 mm, the failure is not simply “too thick” or “too deep.” Deep-cavity behavior becomes visible. Electrode wear accumulates before the floor is reached, debris is harder to evacuate, and wall taper or floor dishing can grow. Use staged electrodes, orbit/jump cycles, and depth checks before final finishing. If the setup ignores that physical progression, the named feature can pass at the accessible face while failing at depth, at the exit, or after unclamping. The Tellurium Copper condition must be included in the same inspection decision.
Technical Context
A shaped graphite or copper electrode approaches the conductive workpiece in dielectric fluid without touching it. At 20–50 mm, Deep-cavity behavior becomes visible. Electrode wear accumulates before the floor is reached, debris is harder to evacuate, and wall taper or floor dishing can grow. Use staged electrodes, orbit/jump cycles, and depth checks before final finishing. Control electrode stiffness, wear, orbit, debris exit, cavity access, and bottom inspection. For Tellurium Copper, the supplied condition still determines support and surface acceptance.
Sinker EDM Capability Reference
| What you're asking | What you can expect |
|---|---|
| Feature types | blind cavities, ribs, shaped pockets, mold details, deep forms, and internal geometry that a traveling wire cannot reach |
| Tolerance | ±0.008–0.030 mm |
| Surface finish | Ra 0.2–6.3 μm |
| Electrode choice | Graphite or copper selected from cavity, finish, and wear needs |
| Primary cavity limit | Depth, rib width, access, and debris evacuation |
| Main limitation | Electrode access and debris evacuation limit deep, narrow blind geometry. |
Thickness Range Reference
| Thickness or depth input | What it means for this process |
|---|---|
| 20–50 mm | Do not convert stock thickness into cavity depth. Deep-cavity decisions must use the actual depth, width and rib aspect ratio. |
| Primary controls | Plan from cavity geometry, electrode access, orbit strategy, rough and finish electrodes, and the strength of the remaining walls. |
Material Condition Reference
| Condition | What to expect | Watch out for | Surface notes |
|---|---|---|---|
| annealed | Use gentle fixturing and adjust energy for high conductivity. | Soft edges can mark or roll under poor support. | Keep contact, bearing, and cosmetic faces as separate finish requirements. |
| half-hard or work-hardened | Balance work-hardening stress with wear compensation. | Thin sections can move and micro features can round as electrodes wear. | Inspect edge radius and functional texture. |
Thickness Impact
Tellurium Copper is a free-machining copper alloy that retains high conductivity while cutting more easily than pure copper. In the 20–50 mm setup, state the supplied condition, support the functional features, and define surface and inspection requirements separately. The material condition changes support and surface response, while Sinker EDM determines how the feature is accessed and controlled.
Surface and Edge Control
For Sinker EDM on Tellurium Copper at 20–50 mm, inspect the functional face or edge from its own datum. Use gentle fixturing and a finish strategy that protects contact, sealing or heat-transfer surfaces. Keep texture, edge condition, recast, corrosion protection, and post-processing as separate acceptance items when service requires them.
Tellurium Copper Sinker EDM Thickness Checkpoints
- Show the actual cavity depth and local wall thickness represented by 20–50 mm, not only the outside part size.
- Plan from cavity geometry, electrode access, orbit strategy, rough and finish electrodes, and the strength of the remaining walls.
- Mark the functional tolerance, finish, datum, and inspection method on the drawing.
Limits and Better Alternatives
Main Limit
The 20–50 mm label cannot replace the real cavity depth and width, rib thickness, electrode access, electrode wear, flushing and debris evacuation or the supplied Tellurium Copper condition. Soft conductive edges and mixed thermal response can make fixturing and finish control more important than cutting force.
Consider Another Route When
Use Wire EDM for through profiles, CNC for open cavities with tool access, or grinding for simple flat precision surfaces.
Practical Next Step
Send the Tellurium Copper drawing with its condition, the actual cavity depth and local wall thickness in the 20–50 mm range, feature geometry, controlled tolerance, surface requirement, quantity, and inspection method.
Practical Takeaway
For Tellurium Copper at 20–50 mm, plan Sinker EDM from the real feature axis, support, debris control, and inspection method instead of treating the range as a blanket capability statement.
Technical Reference
Use the values as planning references and define the functional requirement on the controlled drawing.
Use This Guide to Prepare Your RFQ
Contact us when your drawing and requirements are ready for review.
- Process: Sinker EDM
- Material: Tellurium Copper
- Thickness: 20–50 mm
- Drawing or part sketch
- Material grade
- Thickness / part size
- Quantity
STEP/STP, DXF, DWG, PDF, IGS/IGES or ZIP.
Confidential drawing review. NDA support available on request.